12-22-2015, 09:34 PM
#1
User Info
I'm having difficulty finding shaving brush stands which can fit knots 24mm and greater. What are some shaving brush stands which accommodate larger knots? Any help would be appreciated.

77 369
Reply
 12-22-2015, 09:53 PM
#2
User Info
A few of the vendors, on here, have some, such as Wet Shaving Products and Bullgoose. Good luck.

82 21,056
Reply
 12-23-2015, 08:31 AM
#3
  • Barrylu
  • Senior Member
  • Portland OR
User Info
This works for me.
[Image: mCUvBwv.jpg][Image: JXrOC5N.jpg]

68 1,047
Reply
 12-23-2015, 08:41 AM
#4
User Info
I use an adjustable wooden-based doll stand for some of my larger brushes.  I found them on eBay for around $8 shipped.
[Image: plqKqXA.jpg]

206 12,188
Reply
 12-25-2015, 12:57 PM
#5
  • chazt
  • Senior Member
  • Bayside, NY
User Info
(12-22-2015, 09:53 PM)celestino Wrote: A few of the vendors, on here, have some, such as Wet Shaving Products and Bullgoose. Good luck.

I bought an E. Jagger stand from Bullgoose and have discovered that with some firm but gentle outward pressure the opening can be modified to accomodate a 28mm knot.

4 1,912
Reply
 12-25-2015, 03:46 PM
#6
  • kav
  • Banned
  • east of the sun,west of the moon
User Info
I just stand mine on the counter. If I make a mess sometimes the brush will slide on a cushion of thin lather and water and get attacked by pyewacket.

2 3,171
Reply
 12-25-2015, 04:51 PM
#7
User Info
(12-23-2015, 08:31 AM)Barrylu Wrote: This works for me.
[Image: mCUvBwv.jpg][Image: JXrOC5N.jpg]

Great idea! I didn't know they still make these.  Your Sanitizer is awesome; where did you aquire it?

17 93
Reply
 12-26-2015, 10:01 AM
#8
  • Barrylu
  • Senior Member
  • Portland OR
User Info
Stamp holders are available on Amazon. The sanitizer was from etsy and also can be found on ebay

68 1,047
Reply
 12-31-2015, 02:24 PM
#9
User Info
Walmart sells stamp holders - used for crafters - the nice thing is you can get an extension that goes up. I bought mine on Ebay and the trick is to get one in dent shape.

[Image: e0d76981b7a883fa7bee3b94e155b973.jpg]

Sent via Tapatalk from phone

0 14
Reply
 12-31-2015, 02:49 PM
#10
User Info
Thanks everyone for help. I went ahead and purchased some Edwin Jagger stands and will 'adjust' them accordingly. I only have one stand that can accommodate large knots, so we shall see.

77 369
Reply
 12-31-2015, 06:39 PM
#11
User Info
I have one of those stamp holders. the only problem i had was they were actually marring the handles of my brushes.  There are not a lot of options when it comes to a stand that holds multiple brushes

0 55
Reply
 12-31-2015, 07:21 PM
#12
  • Barrylu
  • Senior Member
  • Portland OR
User Info
Rammer. You missed the modification I posted. Simply put shrink electrical insulation on the metal prongs and apply heat until the insulation shrinks tightly around the metal. See Photo.
[Image: gXna0Oa.jpg]

68 1,047
Reply
 01-05-2016, 04:30 PM
#13
User Info
That is what I did to mine as well. Shrink tubing that can be found in hardware and big box retail stores like Wal-Mart. I picked up a large package at Harbor Freight for short money.

Sent via Tapatalk from phone

0 14
Reply
 01-05-2016, 05:41 PM
#14
User Info
Very helpful on the "stamp" holder and shrink wrap.  

Thanks !!

20 162
Reply
 01-14-2016, 12:12 PM
#15
User Info
Check out em's place they have the holders for bigger brushes.

79 824
Reply
 01-14-2016, 12:46 PM
#16
User Info
(12-25-2015, 03:46 PM)kav Wrote: I just stand mine on the counter. If I make a mess sometimes the brush will slide on a cushion of thin lather and water and get attacked by pyewacket.

That was my vote too.  Handles make excellent brush stands.  Someone even pointed out once that there is a reason why the logos are right-side up when the brush is sitting on the handle...

1 296
Reply
Users browsing this thread: 1 Guest(s)